Re: If you own a constant current ionic silver generator .. (Colloidal Silver Forum) 4/12/2010 1604979

Re: If you own a constant current ionic silver generator ..

Original Hulda Clark
Hulda Clark Cleanses

SilverFox Views: 20,735
Published: 14 y

This is a reply to # 1,604,968

Re: If you own a constant current ionic silver generator ..

Hello Silver is Money,

I like 1.5" spacing...

You use the figure for both electrodes, which in your case is around 2.5 mA.

Tom

All of my messges on this board All of my messges anywhere

Add To Favorites!

Like Dislike

Alert Moderators

DISCLAIMER

This Forum message belongs to a larger discussion thread. See the complete thread below. You can reply to this message!

Expand the next 20 of 32 messages

If you own a constant current ionic silver generat... Silver_Is_Money 14 y 21,286
- I’m also interested in that. If somebody knows ... #68716 14 y 20,810
  - I’m also interested in that. If somebody knows ... Johny Apple Bomb 14 y 22,366
    - If one were to build this circuit, what would be a... ciscokid 14 y 20,836
    - additional circuits to build your automatic CS mak... Gill Grabber 14 y 23,929
      - Hi Gil Thanks for the info you have given here.... Danthemanca 8 y 6,810
    - I don’t really see a problem, but 3ma is about twi... The Silver Genie 14 y 20,205
    - I have not tried this yet, there are simple curren... Gill Grabber 13 y 19,227
- Hello Silver is Money, The general rule is to h... SilverFox 14 y 20,875
  - ”The general rule is to have 1 mA per square inch ... Silver_Is_Money 14 y 21,003
    - In adition to knowing how much current I need, I a... Silver_Is_Money 14 y 20,896
      - In adition to knowing how much current I need, I a... Johny Apple Bomb 14 y 20,868
        
        My homemade system utilizes a magnetic stir bar an... Silver_Is_Money 14 y 20,910
        
        Did you actually measure yours at 1,000 uA (1 mA),... Johny Apple Bomb 14 y 20,897
        
        The 1 mA current and the very long electrodes woul... Silver_Is_Money 14 y 21,027
    - Hello Silver is Money, I like 1.5” spacing... ... SilverFox 14 y 20,735
      This is the position of the above message within the thread.
      - I will increase the spacing to 1.5”, and replace m... Silver_Is_Money 14 y 20,996
        
        I just switched out my roughly 68 ohm resisitor fo... Silver_Is_Money 14 y 20,841
      - Tom, do you have a DMM with which you can properly... Silver_Is_Money 14 y 20,912
  - Tom, is there a reference link that you can point ... Silver_Is_Money 14 y 20,828
    - Expand the next 12 of 32 messages
      
      Hello Silver is Money, Sorry, I don’t know wher... SilverFox 14 y 20,845
      - Well, it just doesn’t get any better than that for... Silver_Is_Money 14 y 20,888
        
        2 resistors? #68716 14 y 20,895
        
        Here’s a nifty conversion site that I have had boo... Iolite 14 y 20,808
        
        Thanks :) But for me the real problem is unders... #68716 14 y 20,975
        
        The LM334Z is a voltage regulator. As the silve... Silver_Is_Money 14 y 20,942
        
        The second resistor and the diode are only for tem... Silver_Is_Money 14 y 20,927
        
        Re: If you own a constant current ionic silver gen... SilverFox 14 y 20,780
        
        OK Tom, I will just double my resistance on the LM... Silver_Is_Money 14 y 20,828
        
        That was easy. 2 x 22 Ohm and 1 x 10 Ohm resistor... Silver_Is_Money 14 y 20,758
        
        If you still have the problem of it taking too lon... Johny Apple Bomb 14 y 20,678
        
        Johny, that’s an excellent idea! For the first go... Silver_Is_Money 14 y 20,817

Donate to CureZone

CureZone Newsletter is distributed in partnership with https://www.netatlantic.com

Contact Us - Advertise - Stats

0.109 sec, (1)

Re: If you own a constant current ionic silver generator ..

This Forum message belongs to a larger discussion thread. See the complete thread below. You can reply to this message!

This is the position of the above message within the thread.