Re: If you own a constant current ionic silver generator .. (Colloidal Silver Forum) 4/16/2010 1607256

Re: If you own a constant current ionic silver generator ..

Energy Awareness Course
Use CureZone kode to get a free session!

Lugol’s Iodine Free S&H
J.Crow’s® Lugol’s Iodine Solution. Restore lost reserves.

Original Dr. Hulda Clark
Hulda Clark Cleanses

Silver_Is_Money Views: 20,829
Published: 14 y

This is a reply to # 1,607,176

Re: If you own a constant current ionic silver generator ..

OK Tom, I will just double my resistance on the LM334Z to about 54 ohms. That will cut my current in half, and bring me to 1 mA per suqare inch of a single electrode.

All of my messges on this board All of my messges anywhere

Add To Favorites!

Like Dislike

Alert Moderators

DISCLAIMER

This Forum message belongs to a larger discussion thread. See the complete thread below. You can reply to this message!

Expand the next 20 of 32 messages

If you own a constant current ionic silver generat... Silver_Is_Money 14 y 21,288
- I’m also interested in that. If somebody knows ... #68716 14 y 20,812
  - I’m also interested in that. If somebody knows ... Johny Apple Bomb 14 y 22,367
    - If one were to build this circuit, what would be a... ciscokid 14 y 20,837
    - additional circuits to build your automatic CS mak... Gill Grabber 14 y 23,931
      - Hi Gil Thanks for the info you have given here.... Danthemanca 8 y 6,812
    - I don’t really see a problem, but 3ma is about twi... The Silver Genie 14 y 20,206
    - I have not tried this yet, there are simple curren... Gill Grabber 13 y 19,228
- Hello Silver is Money, The general rule is to h... SilverFox 14 y 20,877
  - ”The general rule is to have 1 mA per square inch ... Silver_Is_Money 14 y 21,004
    - In adition to knowing how much current I need, I a... Silver_Is_Money 14 y 20,897
      - In adition to knowing how much current I need, I a... Johny Apple Bomb 14 y 20,869
        
        My homemade system utilizes a magnetic stir bar an... Silver_Is_Money 14 y 20,911
        
        Did you actually measure yours at 1,000 uA (1 mA),... Johny Apple Bomb 14 y 20,898
        
        The 1 mA current and the very long electrodes woul... Silver_Is_Money 14 y 21,028
    - Hello Silver is Money, I like 1.5” spacing... ... SilverFox 14 y 20,737
      - I will increase the spacing to 1.5”, and replace m... Silver_Is_Money 14 y 20,997
        
        I just switched out my roughly 68 ohm resisitor fo... Silver_Is_Money 14 y 20,842
      - Tom, do you have a DMM with which you can properly... Silver_Is_Money 14 y 20,913
  - Tom, is there a reference link that you can point ... Silver_Is_Money 14 y 20,829
    - Expand the next 12 of 32 messages
      
      Hello Silver is Money, Sorry, I don’t know wher... SilverFox 14 y 20,846
      - Well, it just doesn’t get any better than that for... Silver_Is_Money 14 y 20,890
        
        2 resistors? #68716 14 y 20,897
        
        Here’s a nifty conversion site that I have had boo... Iolite 14 y 20,810
        
        Thanks :) But for me the real problem is unders... #68716 14 y 20,977
        
        The LM334Z is a voltage regulator. As the silve... Silver_Is_Money 14 y 20,943
        
        The second resistor and the diode are only for tem... Silver_Is_Money 14 y 20,929
        
        Re: If you own a constant current ionic silver gen... SilverFox 14 y 20,782
        
        OK Tom, I will just double my resistance on the LM... Silver_Is_Money 14 y 20,829
        This is the position of the above message within the thread.
        
        That was easy. 2 x 22 Ohm and 1 x 10 Ohm resistor... Silver_Is_Money 14 y 20,760
        
        If you still have the problem of it taking too lon... Johny Apple Bomb 14 y 20,679
        
        Johny, that’s an excellent idea! For the first go... Silver_Is_Money 14 y 20,818

Donate to CureZone

CureZone Newsletter is distributed in partnership with https://www.netatlantic.com

Contact Us - Advertise - Stats

0.109 sec, (1)

Re: If you own a constant current ionic silver generator ..

This Forum message belongs to a larger discussion thread. See the complete thread below. You can reply to this message!

This is the position of the above message within the thread.