Re: First batch done using Utopia generator on default settings MUD by grizz ..... Colloidal Silver Forum
Date: 10/18/2016 8:10:10 AM ( 8 y ago)
Hits: 2,223
URL: https://www.curezone.org/forums/fm.asp?i=2339435
Sorry to say, I would dump that Crappola right into the toilet. It is unfit for human consumption. I would not even give it to my dog. Now you know what Silver MUD is.
I suggest you fix your generator by placing a 1 MAH Current Limiting Diode in series with the positive anode, then install an aquarium bubbler to stir the liquid.
Wiring the Diode by Esstee
//www.curezone.org/forums/fm.asp?i=2259054#i
Where to buy the Diode by Esstee
//www.curezone.org/forums/fm.asp?i=2258964#i
Diodes from Amazon.Com Link
Data Sheets for Diodes - Link - Link
Current limiting diodes work equally well for a wide range of power supplies:
//www.curezone.org/forums/fm.asp?i=2335342#i
Ebay Link
See link details here:
http://tinyurl.com/silver-generators
Does that mean in the above video example, he has MUD and it's not ideal silver...so his settings were wrong in making or he overcooked the batch?
>> YES, either one will create MUD.
I think the silvertron is more set and forget, right... Just set it to low milliamp (1 - 3Ma?) ... and let it run until it shuts off?
>> YES, 3 Ma is too much for the silver wire, OK for the silver bar.
What voltage would I look for ? I'm going to test the voltage with my new utopia generator. And then place a milliamp meter on the anode to see what that reads... I need to see if I have a Ma reader.
>> You expect to see the voltage start high and slowly drop to a low - In my Silvergen Elite, I see volts start at 18 & drop to 10 or less. The milliammeter will start at 0 and slowly go up to the MAX LIMIT then hold steady. I have my silvertron limited to 2Ma MAX for my 1 ounce bar.
So, if the voltage and Ma reading is ideal on the utopia generator, then in theory it will do just as good a job as the silvertron or other generator, correct? I don't think they list the electric measurements for the unit, so I would have to do it myself I believe.
>> They always HIDE the vital numbers for marketing purposes. Feed us BS & keep us dumb. From the results of your batch, I think you have a constant voltage generator:
>> Constant voltage vs constant current pros & cons from SilverGen:
http://www.silvergen.com/technica.htm
Adding that current limiting diode will fix it.
For your silvertron unit, did they ship you the stainless steel electrode to use with the silver bar? Or where did you buy/get it?
>>They shipped a silver wire for the cathode. It doesn't matter what the cathode is, it NEVER wears out. It could be copper, aluminum, etc.
And then one last thing Grizz, when you finish your batch of 20-30ppm silver, I assume thats for internal use?
>> YES, can also be used externally.
Are you converting it after like what the mod recommends on the csforum? Or are you just directly bottling it after it finishes to the end of the process?
>> I don't want anything to do with converting ionic into particulate silver. BIG MISTAKE!
Only the Ionic Silver is capable of killing pathogens. Read the chapter Truths & Lies here:
http://tinyurl.com/colloidal-silver-resources
There can be only ONE truth on the subject of Colloidal Silver . I want the TRUTH, the whole TRUTH and nothing but the TRUTH. You will find 95% lies, distortions, and BS on the internet.
Best to you,
Grizz
<< Return to the standard message view
fetched in 0.01 sec, referred by http://www.curezone.org/forums/fmp.asp?i=2339435